KSC Glock 23f problems

Off_kilter · February 24th, 2011, 18:15

just got her in the mail today and fired it up. It has two problems

1.Horrible gas effeicency

2. Slide doesn't always lock back when empty.

Now it has a metal slide and i greased up the rails.

The pistol apparently does not have much use so it shouldn't be wear and tear.

Any ideas folks?

ILLusion · February 24th, 2011, 18:35

Check the nozzle, piston head and rocket valve for any damage.

Off_kilter · February 24th, 2011, 18:49

on the risk of sounding stupid anyone have some disassembly instructions/video?

CDN_Stalker · February 24th, 2011, 19:32

Regarding the lack of locking back, on the side of the slide lock lever there is a small triangle peice of metal attached, take a pair of pliers and gently bend it DOWN a little bit, like half a millimeter or so (it's stamped steel, so it won't snap easy). That's the lifter and will make the slide lock back every time. I had to do it a couple times to various G19s I had, worked every time.

Gas efficiency, how many rounds per full gas fill? Normal should be about 1.5-2 mags worth, an issue is present when it's less than a full mag. And, how many mags did you get? If the gas effiency is enough to not make the slide travel back enough, this could be the issue you are having with the slide release too.

Regarding disassembly, do you mean to be able to reduce to a pile of frustrating peices? Or how to take the slide off?

BTW, what type of grease was used? Thin or thick?

Off_kilter · February 24th, 2011, 20:16

less then one mags worth of shots.

I can get the slide off after that well I don't want to take apart anything that i'm not suppose to.

The grease I used is thin was thinking of useing thicker.

CDN_Stalker · February 24th, 2011, 20:24

Ya, don't take it apart further than taking the slide off.

What conditions were you using the gun in? Inside/outside? Temp? Am sure you know where I'm going with this, eh numpty?

Off_kilter · February 24th, 2011, 20:27

lol at the numpty reference

inside my room I stride semi and full auto and waited for the mag to warm up between refilling it

CDN_Stalker · February 24th, 2011, 20:29

Figured you'd get that.

I guess you only got one mag with it, eh? And did the usual fill upside down til full and spraying. Propane, duster? Etc, etc. This isn't your first GBB either, right?

BTW, full auto causes rapid cool off, and will make gas efficiency about half of what semi will do if you fire a few shots, wait 10 seconds or more, fire a few more, wait, etc.

Off_kilter · February 24th, 2011, 20:33

my first but my buddy who lives down the hall has experience.

The mag was spewing and slow shooting was better but not much still not a full mag

CDN_Stalker · February 24th, 2011, 20:35

What's the lube situation for oil on the internals, like around the hammer area and such?

Off_kilter · February 24th, 2011, 20:38

it has a light coat and the propane adaptor had silicone oil added before filling the mag

audi_bhoy · February 25th, 2011, 00:10

I assume your propane tank is full? Otherwise if it's nearly empty it might not deliver as much propane a new tank should.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

February 24th, 2011, 18:15	#1
Off_kilter Trader rating Join Date: Aug 2010 Location: From antigonish but posted in Edmonton	KSC Glock 23f problems just got her in the mail today and fired it up. It has two problems 1.Horrible gas effeicency 2. Slide doesn't always lock back when empty. Now it has a metal slide and i greased up the rails. The pistol apparently does not have much use so it shouldn't be wear and tear. Any ideas folks? __________________

February 24th, 2011, 18:35	#2
ILLusion GBB Whisperer Trader rating Join Date: Jun 2002 Location: Toronto	Check the nozzle, piston head and rocket valve for any damage. __________________ *Advanced Airsoft Armaments and Enhancements* Quick to the gun, sure of your grip. Quick to the threat, sure of your shot. Diligentia, Vis, Celeritas Accuracy, Power, Speed

February 24th, 2011, 18:49	#3
Off_kilter Trader rating Join Date: Aug 2010 Location: From antigonish but posted in Edmonton	on the risk of sounding stupid anyone have some disassembly instructions/video? __________________

February 24th, 2011, 19:32	#4
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Regarding the lack of locking back, on the side of the slide lock lever there is a small triangle peice of metal attached, take a pair of pliers and gently bend it DOWN a little bit, like half a millimeter or so (it's stamped steel, so it won't snap easy). That's the lifter and will make the slide lock back every time. I had to do it a couple times to various G19s I had, worked every time. Gas efficiency, how many rounds per full gas fill? Normal should be about 1.5-2 mags worth, an issue is present when it's less than a full mag. And, how many mags did you get? If the gas effiency is enough to not make the slide travel back enough, this could be the issue you are having with the slide release too. Regarding disassembly, do you mean to be able to reduce to a pile of frustrating peices? Or how to take the slide off? BTW, what type of grease was used? Thin or thick? __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871 Last edited by CDN_Stalker; February 24th, 2011 at 19:34..

February 24th, 2011, 20:16	#5
Off_kilter Trader rating Join Date: Aug 2010 Location: From antigonish but posted in Edmonton	less then one mags worth of shots. I can get the slide off after that well I don't want to take apart anything that i'm not suppose to. The grease I used is thin was thinking of useing thicker. __________________

February 24th, 2011, 20:24	#6
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Ya, don't take it apart further than taking the slide off. What conditions were you using the gun in? Inside/outside? Temp? Am sure you know where I'm going with this, eh numpty? __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

February 24th, 2011, 20:27	#7
Off_kilter Trader rating Join Date: Aug 2010 Location: From antigonish but posted in Edmonton	lol at the numpty reference inside my room I stride semi and full auto and waited for the mag to warm up between refilling it __________________

February 24th, 2011, 20:29	#8
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Figured you'd get that. I guess you only got one mag with it, eh? And did the usual fill upside down til full and spraying. Propane, duster? Etc, etc. This isn't your first GBB either, right? BTW, full auto causes rapid cool off, and will make gas efficiency about half of what semi will do if you fire a few shots, wait 10 seconds or more, fire a few more, wait, etc. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

February 24th, 2011, 20:33	#9
Off_kilter Trader rating Join Date: Aug 2010 Location: From antigonish but posted in Edmonton	my first but my buddy who lives down the hall has experience. The mag was spewing and slow shooting was better but not much still not a full mag __________________

February 24th, 2011, 20:35	#10
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	What's the lube situation for oil on the internals, like around the hammer area and such? __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

February 24th, 2011, 20:38	#11
Off_kilter Trader rating Join Date: Aug 2010 Location: From antigonish but posted in Edmonton	it has a light coat and the propane adaptor had silicone oil added before filling the mag __________________

February 25th, 2011, 00:10	#12
audi_bhoy Trader rating Join Date: Mar 2009 Location: Trois-Rivières	I assume your propane tank is full? Otherwise if it's nearly empty it might not deliver as much propane a new tank should.

KSC Glock 23f problems

Doctor's Corner